I looked at the specs of my welder — Thermal Arc 141i — and it says that I need a 5 or 6 Kw generator to run it off grid. Since this one has a PFC module, do I need an inverter generator? Or can I get away with the more common ones? Thanks!

tweake wrote: ↑Fri Nov 18, 2022 4:26 pm depends on the model. anything in the manual about it?
one of mine has an off position. the other is auto off.

Noting in the manual about it... It's a Pro Point helmet, made by Jasic, I think...

I'd like to know what is the better way to save batteries when the hood is not in use: grind mode? Cause mine has a little flashing light to indicate that I am in grind mode (to avoid being flashed); not sure if it is the right way to store my helmet... Thanks very much.

The recommended amperage for the Forney 6011 is 25-75. I used them around 50. No problem to light em, the arc is consistent, but like I said, the flux burns unevenly, ending with a pointy bevel like tip... Never had such a problem with other electrodes... I might crank up the amperage and see... or ...

Same, same... Forney and Blue Demon... Lincoln is a different story, on another machine...

I did compare those 2 on my Esab 161LT... They work fine, except that the Forney had the flux coating burn unevenly... becoming bevel like (like the silicon tube tip that you cut at an angle). I tried the Lincoln Fleetweld on another machine, was also going fine, without that sort of issue. Why is t...

I'd like to use Select arc 700GS for thin sheet metal... seems to work fine. I've heard that if you do not clean the weld slag outside and INSIDE (for a car body panel for exemple), it might conduct to premature corrosion. The thing is, sometimes, it's hard to access the inside panel. I also know th...

Very good indeed! I can weld with very low amperage with a consistent arc! I am very surprised. Can't wait to do some more test... I also had a surprise when I received the welder; full of dust, bad receptacles, bad connectors, etc. Once I took care of it, everything worked flawlessly... I bought it...

I found a very, very good deal on an ESAB Miniarc 161 lts... Runs all the rods that I need, including 6010 in a portable unit... I'll let you once I have tested it thoroughly... Thanks for the reply.

You mean the Esab Rogue 180i... Yeah, seems like a great machine, just more expensive though... The HTP interarc 160 is just 499$. On Ebay, I can certainly get a Rogue 180i for about that amount of money from Dublin Ireland. It is still a dual voltage but I do not know why they would need it in UK. ...

Seems pretty good indeed... I tried to check on their website and its's there but I am arriving on a «page not found». Can you tell us how much you paid for this one?

Good to know it can run 6010 decently... It is hard to figure these days — which one will, based on specs...

Sure... I have all my time...

That would be allright... 160 AMP approx...

My Thermal Arc 141i won't run 6011 either... I tried with Blue Demon 3/32 and the experience confirmed the manufacturer's warning... But I tried Fleetweld 180 6011 3/32 and they worked okay...

I am looking for a stick welder, dual voltage, portable (sub 20 pounds), with an arc force adjustment... 160 amp, 200 amp max out... I am not a big fan of the cheap chinese welder — I bought one and it went back to the source as soon as I received it... I am looking for something middle of the road,...

Hello everybody, Newbie here on this forum... I have a little concern... I am using 3/32 rods; one is 7018 Blue Demon and the other is Lincoln Fleetweld 47 7014... No problem with 7018 BDemon... but the the Lincoln FW 7014, the arc keep shutting down. Both have a similar range in Amp; I use both at ...