Which for TIG welding is not beneficial of course.Poland308 wrote:It's more subtle. These same principles also apply to tig welding. Reversing polarity from electrode neg, to electrode positive causes the heat to be focused into the tungsten more than the base metal.
Stick Welding Tips, Certification tests, machines, projects
- MinnesotaDave
-
Weldmonger
-
Posts:
-
Joined:Sun Oct 27, 2013 10:57 pm
-
Location:Big Lake/Monticello MN, U.S.A.
Dave J.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
Farmwelding
- Farmwelding
-
Weldmonger
-
Posts:
-
Joined:Thu Mar 10, 2016 11:37 pm
-
Location:Wisconsin
Then you have to increase tungsten sizes or drop amperages to avoid melting your tungsten.MinnesotaDave wrote:Which for TIG welding is not beneficial of course.Poland308 wrote:It's more subtle. These same principles also apply to tig welding. Reversing polarity from electrode neg, to electrode positive causes the heat to be focused into the tungsten more than the base metal.
A student now but really want to weld everyday. Want to learn everything about everything. Want to become a knower of all and master of none.
Instagram: @farmwelding
Nick
Instagram: @farmwelding
Nick
- MinnesotaDave
-
Weldmonger
-
Posts:
-
Joined:Sun Oct 27, 2013 10:57 pm
-
Location:Big Lake/Monticello MN, U.S.A.
The benefit is not there, very large tungsten is required to weld at low amps.Farmwelding wrote:Then you have to increase tungsten sizes or drop amperages to avoid melting your tungsten.MinnesotaDave wrote:Which for TIG welding is not beneficial of course.Poland308 wrote:It's more subtle. These same principles also apply to tig welding. Reversing polarity from electrode neg, to electrode positive causes the heat to be focused into the tungsten more than the base metal.
It works for thin aluminum, I've tried it, but isn't very practical.
Dave J.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
After much reading and exchanges , I got that stick welding DCEN allow a quieter and more manageable arc so it is choosed by some for the first root pass (up to some thickness of metal certainly)
Also with thin gauges DCEN is used up to ga13 for instance, then with thicker steel it does not allow good enough penetration.
It makes root pass easier ,less risk of opening a large key hole better management of arc blow, etc.
That is about all I wanted to understand, there may be more subtleties depending of types of coating as different protective gas can be created, but I think I have my answers for the moment.
The shape is still flatter with DCEP, larger than with straight polarity. The names used as "reverse polarity" that mean the opposite for 6013 and 7018 is a big help to obtain much confusion
Best regards, and thanks all for your generous help.
Also with thin gauges DCEN is used up to ga13 for instance, then with thicker steel it does not allow good enough penetration.
It makes root pass easier ,less risk of opening a large key hole better management of arc blow, etc.
That is about all I wanted to understand, there may be more subtleties depending of types of coating as different protective gas can be created, but I think I have my answers for the moment.
The shape is still flatter with DCEP, larger than with straight polarity. The names used as "reverse polarity" that mean the opposite for 6013 and 7018 is a big help to obtain much confusion
Best regards, and thanks all for your generous help.
Last edited by olek on Sun Jun 11, 2017 7:16 am, edited 1 time in total.
Pianos , restorer and tuner
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Is 'R' something you have in mind when welding, for instance modulating your arc lenght you know that you will have a certain effect in metallurgy ? I do not figure that very well yet, for instance I see I create more heat if I enlarge a hair the arc, but what happens when the arc is very short I don't know out that it is good to have a short but tense arc .Poland308 wrote:Resistance is your air gap. Or arc length.
https://en.m.wikipedia.org/wiki/Electroplating
Electron flow plays a part in deposition rates.
Is the arc somewhat tight lor "hard" when very short ? Tension is at its hughest then ? Sorry for the question see that is not yet totally clear even if it is basics.
For instance I think that "manual automatic" (dragging without much pull motion ) allow to use a strong amp, as it is at its lowest when dragging ...
Pianos , restorer and tuner
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Keeping your arc length short is important. I don't ever think about the actual resistance it's creating. I can't think of any good things that happen when your arc is long. It's wasted energy, your machine has to run harder just to maintain the arc. You already noticed the heat increase you get. It's also possible to get it long enough that you don't get proper gas shielding. Undercut, loss of control or arc wander. I'm not sure about the metallurgy part other than that it has some effect mostly from the poor shielding, and a diferance in the metal structure as it's deposited.
I have more questions than answers
Josh
Josh
Hello
back to topic, I was lucky today to have a feel of the difference depending of polarity
on certain metals or may be only on thin or moderately thin, DCEN will penetrate better because of the sharper shape of the arc plus fused metal
the documents provided by the electrodes makers are intended to professionals , I suppose you weld with stronger electrodes than 1/8 and mostly on thick metal, I did see the guide from Lincoln : tables show thick electrodes and very high Amp.
as I see it DCEP became necessary then , to have adequate penetration, hence what say LINCOLN, ESAB, and others
so this is not contradictory in the end, I think,
still DCEN helps by providing a quieter arc and puddle for the type of weld I may have to do
Regards
back to topic, I was lucky today to have a feel of the difference depending of polarity
on certain metals or may be only on thin or moderately thin, DCEN will penetrate better because of the sharper shape of the arc plus fused metal
the documents provided by the electrodes makers are intended to professionals , I suppose you weld with stronger electrodes than 1/8 and mostly on thick metal, I did see the guide from Lincoln : tables show thick electrodes and very high Amp.
as I see it DCEP became necessary then , to have adequate penetration, hence what say LINCOLN, ESAB, and others
so this is not contradictory in the end, I think,
still DCEN helps by providing a quieter arc and puddle for the type of weld I may have to do
Regards
Pianos , restorer and tuner
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
- MinnesotaDave
-
Weldmonger
-
Posts:
-
Joined:Sun Oct 27, 2013 10:57 pm
-
Location:Big Lake/Monticello MN, U.S.A.
You're overthinking this.olek wrote:Hello
back to topic, I was lucky today to have a feel of the difference depending of polarity
on certain metals or may be only on thin or moderately thin, DCEN will penetrate better because of the sharper shape of the arc plus fused metal
the documents provided by the electrodes makers are intended to professionals , I suppose you weld with stronger electrodes than 1/8 and mostly on thick metal, I did see the guide from Lincoln : tables show thick electrodes and very high Amp.
as I see it DCEP became necessary then , to have adequate penetration, hence what say LINCOLN, ESAB, and others
so this is not contradictory in the end, I think,
still DCEN helps by providing a quieter arc and puddle for the type of weld I may have to do
Regards
You want less penetration on thin metal, that's why the use of DCEN when needed.
You generally want more penetration when dealing with thicker metal, so use DCEP, or don't, it's up to you in the end.
Dave J.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
Yes , Dave, as a "virtual welder" ,without instructor, I overthink before going real
that helps in the end to analyse my mistakes better, I think
the shape of the heat is supposedly different. More sharp in straight polarity. It may be better then for thinner metal as it is more difficult to burn thru .
DCEN is used here very often for root pass to have a neater job more easily no enlarged key hole etc
I try to find reasons when there are contradictions (some manual state that the dcen is deeper, but with no mention of electrode size and polarite this is worthless)
So it helps but then may be there is something relative to the size of the electrode that make some transfer mode more efficient.
I clearly did see dcep refusing to weld , sliding on the surface of the metal even on a precedent bead .
It may be well more quality vs deepness but the heat shape is still sharper. Regards
that helps in the end to analyse my mistakes better, I think
the shape of the heat is supposedly different. More sharp in straight polarity. It may be better then for thinner metal as it is more difficult to burn thru .
DCEN is used here very often for root pass to have a neater job more easily no enlarged key hole etc
I try to find reasons when there are contradictions (some manual state that the dcen is deeper, but with no mention of electrode size and polarite this is worthless)
So it helps but then may be there is something relative to the size of the electrode that make some transfer mode more efficient.
I clearly did see dcep refusing to weld , sliding on the surface of the metal even on a precedent bead .
It may be well more quality vs deepness but the heat shape is still sharper. Regards
Last edited by olek on Sat Jun 24, 2017 10:02 am, edited 2 times in total.
Pianos , restorer and tuner
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
- MinnesotaDave
-
Weldmonger
-
Posts:
-
Joined:Sun Oct 27, 2013 10:57 pm
-
Location:Big Lake/Monticello MN, U.S.A.
My opinion is you may not be proficient enough to know what you are seeing.olek wrote:Yes , Dsve, as a "virtual welder" , I overthink before going real
What are the most common size of your electrodes? (Is my thought about big electrodes for profesdional welders true ?)
helped me .. the shape of the heat is different. More sharp in straight polarity. It may be better then for thinner metal as it is more difficult to burn thru .
DCEN is used here very often for root pass to have a neater job more easily no enlarged key hole etc
I try to find reasons when there are contradictions (some manual state that the dcen is deeper, but with no mention of electrode size and polarite this is worthless)
So it helps but then may be there is something relative to the size of the electrode that make some transfer mode more efficient.
I clearly did see dcep refusing to weld , sliding on the surface of the metal even on a precedent bead .
It may be well more quality vs deepness but the heat shape is still sharper. Regards
If you can't weld on DCEP then you need to practice more, type less - lol
Dave J.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
Return to “Stick Welding/Arc Welding - Shielded Metal Arc Welding”
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities