Good answer Coldie. Not to change the subject...just curious...do you guys have American cars down under?Coldman wrote:Zoomed the pic for a closer look.
I recon there is little chance the chassis is not out of alignment. I don't think cut-bash-reweld will fix it strength for safety or geometrically.
You need to replace that section on a chassis table.
Tig welding tips, questions, equipment, applications, instructions, techniques, tig welding machines, troubleshooting tig welding process
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
I have a offer in on this car based on worst case. If and when it gets here, the first thing that happens is the door and rocker panel come off and 8 measurements will be taken. If those 8 measurements jive, I will be doing minor surgery and not a transplant. A transplant includes a lot of cutting and welding of much more critical areas then where I want to cut and weld.
If half the rail does in fact have to be replaced then so be it. I can't do any more damage to what's there by trying. There is nothing critical in that spot but it does need to be flat in that section to remount the windshield washer tank
If half the rail does in fact have to be replaced then so be it. I can't do any more damage to what's there by trying. There is nothing critical in that spot but it does need to be flat in that section to remount the windshield washer tank
We have cars from all over including American. Petrol heads drool over camaros, vettes and mustangs. We even have an Australian compliant mustang right hand drive out of the factory sold by Ford Australia. Both Ford Australia and GM are shutting down their Australian factories shortly and all future models will be imported. I prefer the classic muscle cars myself. My friend is restoring a 33 chevy (coupe?) right now but fitting a new 350 and he's a pom.exnailpounder wrote:Good answer Coldie. Not to change the subject...just curious...do you guys have American cars down under?Coldman wrote:Zoomed the pic for a closer look.
I recon there is little chance the chassis is not out of alignment. I don't think cut-bash-reweld will fix it strength for safety or geometrically.
You need to replace that section on a chassis table.
Sent using Tapatalk
Flat out like a lizard drinkin'
If you are successful and you manage to get it retested and certified, then you might be placing yourself ahead of the coming curve for future repairs like this. That kind of experience could be very profitable. Might not be the path your planning on, but money talks.
I have more questions than answers
Josh
Josh
Been there, done that turning 62 in a week and have zero interest in any new profit venture. This is just a fun project to work on with my book worm son who has zero mechanical skills. I come from a family of master Mr. Fix-it's. Have to try to pass some of that on along with some tool safety. Right now if you asked him to tell you what color my newest welder is he's sayPoland308 wrote:If you are successful and you manage to get it retested and certified, then you might be placing yourself ahead of the coming curve for future repairs like this. That kind of experience could be very profitable. Might not be the path your planning on, but money talks.
"what's a welder"
For what it's worth, the answer is green.
If I do this job I'll be forced to buy a new TIG torch. This big 250 amp water cooled torch sucks for working on small projects in tight quarters Need a nice 150-200 amp air cooled flex-loc with that nice small flex cable. The cable on the torch I have is like a vacuum cleaner hose.
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
Thanks Coldie...I have never been out of this country before and always wonder about other places. Man...I always knew the major manufacturers were monster corporations but apparently they're way bigger than I thought. What about Harleys?Coldman wrote:We have cars from all over including American. Petrol heads drool over camaros, vettes and mustangs. We even have an Australian compliant mustang right hand drive out of the factory sold by Ford Australia. Both Ford Australia and GM are shutting down their Australian factories shortly and all future models will be imported. I prefer the classic muscle cars myself. My friend is restoring a 33 chevy (coupe?) right now but fitting a new 350 and he's a pom.exnailpounder wrote:Good answer Coldie. Not to change the subject...just curious...do you guys have American cars down under?Coldman wrote:Zoomed the pic for a closer look.
I recon there is little chance the chassis is not out of alignment. I don't think cut-bash-reweld will fix it strength for safety or geometrically.
You need to replace that section on a chassis table.
Sent using Tapatalk
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
noddybrian
- noddybrian
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 24, 2013 12:13 pm
I bet the " motor cycle club " members have watched every episode of the " training program " !
Yes - Sons of Anarchy has a lot to answer for here !
Yes - Sons of Anarchy has a lot to answer for here !
Return to “Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding”
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities