[AKweldshop]

I'll have less than $20 in it when I'm done.

Pics later.

~John

[Superiorwelding]

John,
What's up with that? I got all excited to look at your table and there was no pitures.
-Jonathan

[AKweldshop]

I'm blocked from pics for a little while.

Let me sort it out.

~John

[Antorcha]

Is it a conversion from a bench at Glacier NP ?

[AKweldshop]

This table started out as the fabbed together bunch of channel.

And this 5'x10' sheet of 3/8 steel.

IMG_1937.JPG (118.99 KiB) Viewed 13971 times

IMG_1938.JPG (93.44 KiB) Viewed 13971 times

IMG_1946.JPG (77.56 KiB) Viewed 13971 times

[AKweldshop]

IMG_1942.JPG (58.2 KiB) Viewed 13969 times

IMG_2018.JPG (78.39 KiB) Viewed 13969 times

IMG_2020.JPG (86.42 KiB) Viewed 13969 times

[AKweldshop]

IMG_2021.JPG (82.21 KiB) Viewed 13966 times

IMG_2022.JPG (82.62 KiB) Viewed 13966 times

IMG_2024.JPG (97.08 KiB) Viewed 13966 times

[AKweldshop]

$10 in blades, and I had a 3'x7' slab....

IMG_2041.JPG (127.91 KiB) Viewed 13964 times

IMG_2048.JPG (104.58 KiB) Viewed 13964 times

IMG_2049.JPG (123.13 KiB) Viewed 13964 times

[AKweldshop]

IMG_2056.JPG (70.74 KiB) Viewed 13959 times

IMG_2057.JPG (81.13 KiB) Viewed 13959 times

IMG_2085.JPG (74.56 KiB) Viewed 13959 times

[noddybrian]

Nice bit of re-cycling - it must be nice living where you are - seems like there's plenty of old steel & bits laying around for cheap if you have the ability to use them - no such luck here - last decent scrapyard got shut down a few years back - nothing around now - if I need metal it all has to be bought new which can make side projects real expensive - not sure I'd like how long your winters are though.

[AKweldshop]

For some reason I like it up here.
Been here almost 15yrs.

Lots of auctions, tool loaded yard sales, and deals.

Winters are easily overcome, get a large warm shop.

John

[noddybrian]

The bits visible in your photos looks like a nice place to be - in my ignorance the only things I know about your state are from watching Ice Road Truckers / Bering sea gold / Ax Men / Deadliest Catch - these are some of my favorite TV programs - naturally we don't get them here - but that's what piracy is for right ? !!

[mcoe]

I am going to have to build me a good table. The only tables I have are a cheap 3' x 2' table from northern tool, very cheap piece of junk now, and a piece of scrap that is about 14"x 4'. I need to start one of these projects. Very nice table.

[AKweldshop]

Gentleman....
Finally got to putting a bottom shelf in.

Got some 17" wide sheets of 3/4' plywood at the dump.
Enjoy the pics, and yes, I'm loving this table!!!!

IMG_5626.JPG (48.03 KiB) Viewed 11794 times

IMG_5627.JPG (56.29 KiB) Viewed 11794 times

IMG_5628.JPG (51.22 KiB) Viewed 11794 times

[AKweldshop]

IMG_5629.JPG (56.36 KiB) Viewed 11794 times

IMG_5630.JPG (51.3 KiB) Viewed 11794 times

IMG_5633.JPG (79.27 KiB) Viewed 11794 times

[AKweldshop]

IMG_5634.JPG (79.32 KiB) Viewed 11794 times

IMG_5636.JPG (63.29 KiB) Viewed 11794 times

2 pieces on 1 1/2" angle iron.

IMG_5637.JPG (60.4 KiB) Viewed 11794 times

[AKweldshop]

IMG_5638.JPG (122.27 KiB) Viewed 11793 times

IMG_5639.JPG (62.79 KiB) Viewed 11793 times

IMG_5640.JPG (63.24 KiB) Viewed 11793 times

[AKweldshop]

IMG_5641.JPG (45.79 KiB) Viewed 11792 times

IMG_5642.JPG (33.09 KiB) Viewed 11792 times

IMG_5643.JPG (79.25 KiB) Viewed 11792 times

[AKweldshop]

IMG_5644.JPG (56.46 KiB) Viewed 11792 times

IMG_5649.JPG (94.22 KiB) Viewed 11792 times

IMG_5650.JPG (92.53 KiB) Viewed 11792 times

[AKweldshop]

IMG_5651.JPG (63.31 KiB) Viewed 11791 times

IMG_5652.JPG (94.8 KiB) Viewed 11791 times

Gotta get my shop all organized, been a mess for a while....

I'm thinking of stacking all my 50lb boxes on this shelf, and free up my other table.

IMG_3871.JPG (51.28 KiB) Viewed 11791 times

[mcoe]

LOOK AT ALL THOSE 6013's

[AKweldshop]

LOOK AT ALL THOSE 6013's

Bahahaha!!!!!
Not a lick of them in my shop...