Search found 188 matches
- by Jakedaawg
- Thu Mar 11, 2021 6:38 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Cracks in center of weld
- Replies: 25
- Views: 2471
Re: Cracks in center of weld
Hot short cracking with 4043 is common. Its a base metal dilution issue. I am not smart enough to explain it, maybe someone else here can pick up the ball. I am sure you can Google it.
- by Jakedaawg
- Fri Mar 05, 2021 8:00 am
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: To Replace My Old Machine or not?
- Replies: 20
- Views: 2519
Re: To Replace My Old Machine or not?
Sorry to barge in here...quick one answer question...what is Lincolns' answer to the 255?
- by Jakedaawg
- Sat Feb 27, 2021 5:57 pm
- Forum: Member Introductions
- Topic: Welding on a crankshaft
- Replies: 9
- Views: 2003
Re: Welding on a crankshaft
You absolutely will not be able to keep the top seal from being damaged. I would wrap that area in wet rags... These cranks are a dime a dozen. Simple to tear down and replace with new bearings. I have done a couple. Those motors had a corrosion issue in a water passage. Any marine salvage yard will...
- by Jakedaawg
- Tue Feb 23, 2021 7:34 am
- Forum: Member Introductions
- Topic: Welding on a crankshaft
- Replies: 9
- Views: 2003
Re: Welding on a crankshaft
What motor are you working on? This is what I do. I have parts motors going back to 1935.
- by Jakedaawg
- Tue Feb 16, 2021 9:57 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Tig cast iron fry pan?
- Replies: 14
- Views: 1534
Re: Tig cast iron fry pan?
To the OP, will you please update this thread when you finish the project. I have a cracked cast iron pan that I'd like to repair. Its a much nicer pan than the lodge, so replacement is not cheap.
- by Jakedaawg
- Tue Feb 16, 2021 9:55 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Tig cast iron fry pan?
- Replies: 14
- Views: 1534
Re: Tig cast iron fry pan?
I am no expert here. With that said you might investigate whether Al bronze is good where heating and cooling repeatedly are expected.
- by Jakedaawg
- Sat Feb 06, 2021 9:01 pm
- Forum: Welding Forum General Shop Talk
- Topic: Bending 6061 ?
- Replies: 14
- Views: 1541
Re: Bending 6061 ?
Does the project require 6061 t6? I've been able to do some pretty aggressive spinning and bending with 5052 and I am not a huge metal working place, just a small marine service shop.
- by Jakedaawg
- Wed Jan 27, 2021 12:44 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Welding 1/2" to 1/16" Alum
- Replies: 20
- Views: 2656
Re: Welding 1/2" to 1/16" Alum
You are saying the 1/2" plate is really a little round piece with a 1/2" diameter and 1/2" thickness? The tubing is 1/2" diameter?
- by Jakedaawg
- Mon Jan 25, 2021 5:00 pm
- Forum: Welding Forum General Shop Talk
- Topic: Some doubts regarding welding
- Replies: 3
- Views: 863
Re: Some doubts regarding welding in a car
If you are referring to the body panel seam its likely fancy glue.
- by Jakedaawg
- Mon Jan 25, 2021 4:58 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: The what I welded today (/whenever) thread (pics please)
- Replies: 3253
- Views: 491937
Re: The what I welded today (/whenever) thread (pics please)
I only use those furick glass cups when I absolutely have to. I seem to break one every time I put it on the torch. Sure is nice in dark tight spaces though. I especially like them if I'm using a mirror to see where I'm going. I dont ha e the luxury of welding on a table though. Usually on my back u...
- by Jakedaawg
- Fri Jan 22, 2021 6:12 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Lincoln Tig 200 Square Wave, anyone using?
- Replies: 17
- Views: 7223
Re: Lincoln Tig 200 Square Wave, anyone using?
I cant understand folks who complain about the post flow wasting gas. Granted, the customer pays for my gas but I find the cost of gas inconsequential. It just blows my mind.
- by Jakedaawg
- Mon Dec 28, 2020 9:11 pm
- Forum: Welding Projects - Welding project Ideas - Welding project plans
- Topic: Another Welder cart
- Replies: 7
- Views: 1973
Re: Another Welder cart
Have you ever used a dynasty? Could you post a review of your aspect? Disregard if its not an ac/dc tig machine. I've had my dynasty for 4 years and its getting a ton of hours on it. I'm thinking of picking up another but I want to consider the comparable Lincoln model.
- by Jakedaawg
- Thu Dec 24, 2020 3:02 pm
- Forum: Welding Forum General Shop Talk
- Topic: Annealing and then hardening of 5052 or similar
- Replies: 22
- Views: 3225
Re: Annealing and then hardening of 5052 or similar
Thanks for your experience and observations. The prototypes i have made were done by heating with a weed burner type rig. I then let it cool. Spun it over my die I guess you would call that, then welded in my bent parts over a void thats cut out with a pattern. I dont know how hot I got them. Hot en...
- by Jakedaawg
- Thu Dec 24, 2020 11:16 am
- Forum: Welding Forum General Shop Talk
- Topic: Annealing and then hardening of 5052 or similar
- Replies: 22
- Views: 3225
Re: Annealing and then hardening of 5052 or similar
I am also thinking that it may not really matter in my case. Pontoon companies use this stuff all the time. They bend it, weld it, spin it for end caps, etc. They do things as cheap as possible. I guarantee they dont have any heat treating going on. Perhaps they do this without annealing. Maybe I ju...
- by Jakedaawg
- Thu Dec 24, 2020 11:05 am
- Forum: Welding Forum General Shop Talk
- Topic: Annealing and then hardening of 5052 or similar
- Replies: 22
- Views: 3225
Re: Annealing and then hardening of 5052 or similar
Thanks guys. I appreciate the knowledge. I now have some idea of what information and practices I am looking to learn.
- by Jakedaawg
- Wed Dec 23, 2020 6:24 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Argon gas issues driving me nuts
- Replies: 9
- Views: 2515
Re: Argon gas issues driving me nuts
Can you hook your tank to the welder at work? This would isolate tank and welder.
- by Jakedaawg
- Tue Dec 22, 2020 4:54 pm
- Forum: Welding Forum General Shop Talk
- Topic: Annealing and then hardening of 5052 or similar
- Replies: 22
- Views: 3225
Re: Annealing and then hardening of 5052 or similar
Well, maybe I just need to figure out how to bend it without annealing it.
- by Jakedaawg
- Sun Dec 20, 2020 7:36 pm
- Forum: Welding Forum General Shop Talk
- Topic: Annealing and then hardening of 5052 or similar
- Replies: 22
- Views: 3225
Re: Annealing and then hardening of 5052 or similar
I guess what that is saying is make my part and use will return it to its normal state.
- by Jakedaawg
- Sun Dec 20, 2020 5:14 pm
- Forum: Welding Forum General Shop Talk
- Topic: Annealing and then hardening of 5052 or similar
- Replies: 22
- Views: 3225
Annealing and then hardening of 5052 or similar
Well, let's say you have some 5052 ~.060-~.100. Let's say you anneal it so you can form it to the complex curvy shape you want. How then do you get it back to its pre-annealing (if you will) hardness/strength. I dont really want to put into the airwaves what exactly I am building. Think pontoon type...
- by Jakedaawg
- Sat Dec 19, 2020 12:42 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: The what I welded today (/whenever) thread (pics please)
- Replies: 3253
- Views: 491937
Re: The what I welded today (/whenever) thread (pics please)
Never would have thunk that. Hope they dont regret. Good on you for knowing...looks like quite a pain building that.
- by Jakedaawg
- Sat Dec 19, 2020 12:10 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: The what I welded today (/whenever) thread (pics please)
- Replies: 3253
- Views: 491937
Re: The what I welded today (/whenever) thread (pics please)
I've never seen a dump trailer with the skin on the outside. What am I missing? Won't the load hang up on the verticals?
- by Jakedaawg
- Wed Dec 16, 2020 7:55 am
- Forum: Product Reviews
- Topic: Optrel Panoramaxx CLT welding helmet, with Isofit headgear
- Replies: 16
- Views: 7389
Re: Optrel Panoramaxx CLT welding helmet, with Isofit headge
Good for you. Free helmet in exchange for honest review. Pays to be a prolific poster wink, wink. That headgear looks fragile. Does it feel fragile? Seems like all the little pokey bits would snap off in short order. What is your perception? Maybe after you've used it for 40 hours or so we could hea...
- by Jakedaawg
- Wed Dec 16, 2020 7:20 am
- Forum: Metal Cutting
- Topic: Oxy Propane Residential
- Replies: 10
- Views: 2099
Re: Oxy Propane Residential
I thinknwhenever you deal with the government, whether local or state, its always better to ask forgiveness than permission.
- by Jakedaawg
- Wed Dec 09, 2020 8:26 pm
- Forum: Welding Forum General Shop Talk
- Topic: The darn candy store came to the shop again
- Replies: 3
- Views: 828
Re: The darn candy store came to the shop again
Interesting setup. It will work perfect for me. I weld pretty much marine related things. Skegs, outdrives, boarding ladders on a daily basis. I've been using an old stainless sailboat center board propped on sawhorses for a few years. No way to fixture really. This will be great. Also saves time f...
- by Jakedaawg
- Wed Dec 09, 2020 7:00 pm
- Forum: Welding Forum General Shop Talk
- Topic: The darn candy store came to the shop again
- Replies: 3
- Views: 828
The darn candy store came to the shop again
- newusedtable.jpg (87.64 KiB) Viewed 828 times
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities